Skip to main content

Working of air conditioner


Air conditioners and refrigerators work the same way. Instead of cooling just the small, insulated space inside of a refrigerator, an air conditioner cools a room, a whole house, or an entire business.

Air conditioners use chemicals that easily convert from a gas to a liquid and back again. This chemical is used to transfer heat from the air inside of a home to the outside air.

The machine has three main parts. They are a compressor, a condenser and an evaporator. The compressor and condenser are usually located on the outside air portion of the air conditioner. The evaporator is located on the inside the house, sometimes as part of a furnace. That's the part that heats your house.

The working fluid arrives at the compressor as a cool, low-pressure gas. The compressor squeezes the fluid. This packs the molecule of the fluid closer together. The closer the molecules are together, the higher its energy and its temperature.

The working fluid leaves the compressor as a hot, high pressure gas and flows into the condenser. If you looked at the air conditioner part outside a house, look for the part that has metal fins all around. The fins act just like a radiator in a car and helps the heat go away, or dissipate, more quickly.

When the working fluid leaves the condenser, its temperature is much cooler and it has changed from a gas to a liquid under high pressure. The liquid goes into the evaporator through a very tiny, narrow hole. On the other side, the liquid's pressure drops. When it does it begins to evaporate into a gas.

As the liquid changes to gas and evaporates, it extracts heat from the air around it. The heat in the air is needed to separate the molecules of the fluid from a liquid to a gas.

The evaporator also has metal fins to help in exchange the thermal energy with the surrounding air.
By the time the working fluid leaves the evaporator, it is a cool, low pressure gas. It then returns to the compressor to begin its trip all over again.

Connected to the evaporator is a fan that circulates the air inside the house to blow across the evaporator fins. Hot air is lighter than cold air, so the hot air in the room rises to the top of a room.
There is a vent there where air is sucked into the air conditioner and goes down ducts. The hot air is used to cool the gas in the evaporator. As the heat is removed from the air, the air is cooled. It is then blown into the house through other ducts usually at the floor level.

This continues over and over and over until the room reaches the temperature you want the room cooled to. The thermostat senses that the temperature has reached the right setting and turns off the air conditioner. As the room warms up, the thermostat turns the air conditioner back on until the room reaches the temperature.
Labels:

Comments

Post a Comment

Popular posts from this blog

Bevel protractor

What is bevel protractor ? A bevel protractor is a graduated circular protractor with one pivoted arm used for measuring or marking off angles. Sometimes Vernier scales are attached to give more precise readings. It has wide application in architectural and mechanical drawing, although its use is decreasing with the availability of modern drawing software or CAD. Universal bevel protractors are also used by toolmakers, as they measure angles by mechanical contact they are classed as mechanical protractors. The bevel protractor is used to establish and test angles to very close tolerances. It reads to 5 minutes or 1/12° and can measure any angle from 0° to 360°. The bevel protractor consists of a beam, a graduated dial and a blade which is connected to a swivel plate (with Vernier scale) by thumb nut and clamp. When the edges of the beam and blade are parallel, a small mark on the swivel plate coincides with the zero line on the graduated dial. To m...
Post a Comment
Read more

IC Engine

You all are aware from this word IC Engine, but still don't know what exactly it is. "An  internal combustion engine  (ICE) is a heat  engine  where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit." The  internal combustion engine  is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an oxidizer creates gases of high temperature and pressure, which are permitted to expand. The defining feature of an internal combustion engine is that useful work is performed by the expanding hot gases acting directly to cause movement, for example by acting on pistons, rotors, or even by pressing on and moving the entire engine itself. This contrasts with external combustion engines, such as steam engines, which use the combustion process to heat ...
Post a Comment
Read more

Torque convertor

Torque converter is a type of fluid coupling that uses a fluid to transmit turning effort from the one shaft to another. It is a device which performs a function similar to that of a gear box, namely, to increase the torque while reducing the speed. A gear box provides only a small number of fixed ratios, but the torque converter provides a continuous variation of ratio from the lowest to the highest.The torque convertor is somewhat similar to a fluid fly wheel, but differs from it in one aspect, namely it has three principal components instead of only two. Torque converter consists of (i)  The driving element or impeller or pump which is connected to the engine. (ii)  The driven element or rotor or turbine which is connected to the propeller shaft and (iii)  The fixed element or reaction member or stator which is fixed to the frame. The fixed element is responsible to cause a change of torque between input and output shafts. The fluid flywheel does not ...
Post a Comment
Read more