Skip to main content

Torque convertor


Torque converter is a type of fluid coupling that uses a fluid to transmit turning effort from the one shaft to another. It is a device which performs a function similar to that of a gear box, namely, to increase the torque while reducing the speed. A gear box provides only a small number of fixed ratios, but the torque converter provides a continuous variation of ratio from the lowest to the highest.The torque convertor is somewhat similar to a fluid fly wheel, but differs from it in one aspect, namely it has three principal components instead of only two.


Torque converter consists of
(i) The driving element or impeller or pump which is connected to the engine.
(ii) The driven element or rotor or turbine which is connected to the propeller shaft and
(iii) The fixed element or reaction member or stator which is fixed to the frame. The fixed element is responsible to cause a change of torque between input and output shafts. The fluid flywheel does not have any fixed member, as such cannot produce any change of torque.
Working of a torque converter
The three element torque converter can be seen in the picture. In the torque converter, torque multiplication take place in the following way. The oil leaving vanes hits the stator vanes. This oil is redirected into the pump vanes in a direction which helps the pump operation. This oil is again thrown into the turbine by the pump. In fact, this is a continuous process. The fluid pushing repeatedly on the turbine vanes increases the torque on the turbine. In many designs of torque converters, the torque is almost doubled. However, as the speed of the turbine approaches the speed of the pump, the increase in torque falls of gradually till it becomes 1:1. At this stage, the oil starts striking the rear faces of the vanes in the stator, thus making the stator to turn. Now the stator does not take part in torque converter action. Under these conditions, the torque converter simply acts as a fluid fly-wheel.
The over running clutch or freewheeling device is used for mounting the stator. The spring loaded rollers in the freewheel allow the stator to freewheel when the oil starts striking the rear of the stator vanes. On the other hand, when the oil strikes the front of the stator vanes, it attempts to rotate the stator in the opposite direction. But this action locks up the freewheeling device and thus holds the stator stationary. Under such condition, the stator acts as a reaction member, and directs the oil leaving the turbine trailing edges in the proper direction before it enters the pump vanes.
Labels:

Comments

Post a Comment

Popular posts from this blog

IC Engine

You all are aware from this word IC Engine, but still don't know what exactly it is. "An  internal combustion engine  (ICE) is a heat  engine  where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit." The  internal combustion engine  is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an oxidizer creates gases of high temperature and pressure, which are permitted to expand. The defining feature of an internal combustion engine is that useful work is performed by the expanding hot gases acting directly to cause movement, for example by acting on pistons, rotors, or even by pressing on and moving the entire engine itself. This contrasts with external combustion engines, such as steam engines, which use the combustion process to heat ...
Post a Comment
Read more

Bevel protractor

What is bevel protractor ? A bevel protractor is a graduated circular protractor with one pivoted arm used for measuring or marking off angles. Sometimes Vernier scales are attached to give more precise readings. It has wide application in architectural and mechanical drawing, although its use is decreasing with the availability of modern drawing software or CAD. Universal bevel protractors are also used by toolmakers, as they measure angles by mechanical contact they are classed as mechanical protractors. The bevel protractor is used to establish and test angles to very close tolerances. It reads to 5 minutes or 1/12° and can measure any angle from 0° to 360°. The bevel protractor consists of a beam, a graduated dial and a blade which is connected to a swivel plate (with Vernier scale) by thumb nut and clamp. When the edges of the beam and blade are parallel, a small mark on the swivel plate coincides with the zero line on the graduated dial. To m...
Post a Comment
Read more

Competitions for mechanical engineers

There are various competitions in which you can participate during your graduation. SAE (society of automative engineers) organize three major events every year :  1. BAJA SAE- design and build an all terrain vehicle 2. SUPRA SAE- design and build a formula type race car 3. EffiCycle- design and build a hybrid cycle ASME  ( american society of mechanical engineers) organize human powered vehicle challenge HPVC. ISNE - It organizes go karting championship. If you have interest in automobiles then these competitions will definitely helps you to improve your skills.I was participated in SUPRA SAE (2016).It was a cool experience for me and helps me to improve my basic knowledge. Please like ,share and comment. Subscribe for more updates. Saurabh_savy 
Post a Comment
Read more